rigsmtr(1) measure S-Meter vs azimuth using Hamlib

SYNOPSIS

rigsmtr [OPTION]... [time_step]

DESCRIPTION

rigsmtr uses Hamlib to control a rig to measure S-Meter vs azimuth:
It rotates the antenna from minimum azimuth to maximum azimuth. Every second or time_step if specified in seconds, it retrieves the signal strength.
Azimuth in degree and corresponding S-Meter level in dB relative to S9 are then printed on stdout.
To work correctly, rigsmtr needs a rig that could measure S-Meter and a Hamlib backend that is able to get it, mounted on a Hamlib supported rotator.

Keep in mind that Hamlib is still BETA level software. A lof of stuff hasn't been tested thoroughly, and the API may change without publicised notice. Please report bugs and feedback at the e-mail address given in the REPORTING BUGS section.

OPTIONS

This program follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below.
-m, --model=id
Select radio model number. See model list provided by rigctl.
-r, --rig-file=device
Use device as the file name of the radio to operate on.
-s, --serial-speed=baud
Set radio serial speed to baud rate. Uses maximal rig speed as default.
-c, --civaddr=id
Use id as the CI-V address to communicate with the rig. Only for Icom rigs. NB: the id is in decimal, unless prefixed by 0x, in which case it is hexadecimal.
-C, --set-conf=parm=val[,parm=val]*
Set radio config parameter. See -L option of rigctl for a list.
-M, --rot-model=id
Select radio model number. See model list provided by rotctl.
-R, --rot-file=device
Use device as the file name of the rotator to operate on.
-S, --rot-serial-speed=baud
Set rotator serial speed to baud rate. Uses maximal speed as default.
-N, --rot-set-conf=parm=val[,parm=val]*
Set rotator config parameter. See -L option of rotctl for a list.
-v, --verbose
Set verbose mode, cumulative (BUG, ERR, WARN, VERBOSE, TRACE).
-h, --help
Show summary of options and exit.
-V, --version
Show version of program and exit.

RETURN VALUE

rigsmtr exits with: 0 if all operations went fine; 1 if there was an invalid command line option or arg; 2 if an error was returned by Hamlib; 3 if the rig doesn't have the required capabilities.

EXAMPLE

rigsmtr -m 209 -r /dev/ttyS1 -M 202 > csmtr


Collect S-Meter readings on a TS850 while an EasycommII rotator makes a full 360°, and record measurements in file csmtr.
After completion, csmtr file contains for example the following lines :

  0 -47

  30 -40

  60 -22

  90 -3

  120 10

  150 1

  180 -11

  210 -24

  240 -35

  270 -42

  300 -48

  330 -51

  360 -49

Result could then be ploted with gnuplot:

gnuplot
set angles degrees
set polar
set grid polar 15.
unset border
unset param
set style data line
set rrange [-60:60]
set xrange [-60:60]
set yrange [-60:60]
plot "csmtr"

AUTHOR

Man page written by Stephane Fillod.

BUGS

Need more testing. Reports are welcome.

REPORTING BUGS

Report bugs to <[email protected]>.

COPYRIGHT

Copyright © 2004-2009 Thierry Leconte & Stephane Fillod
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.