SYNOPSISwvdial [ OPTIONS ] [ SECTION ] ...
DESCRIPTIONwvdial is an intelligent PPP dialer, which means that it dials a modem and starts PPP in order to connect to the Internet. It is something like the chat(8) program, except that it uses heuristics to guess how to dial and log into your server rather than forcing you to write a login script.
When wvdial starts, it first loads its configuration from /etc/wvdial.conf and ~/.wvdialrc which contains basic information about the modem port, speed, and init string, along with information about your Internet Service Provider (ISP), such as the phone number, your username, and your password.
Then it initializes your modem and dials the server and waits for a connection (a CONNECT string from the modem). It understands and responds to typical connection problems (like BUSY and NO DIALTONE).
Any time after connecting, wvdial will start PPP if it sees a PPP sequence from the server. Otherwise, it tries to convince the server to start PPP by doing the following:
- responding to any login/password prompts it sees;
- interpreting "choose one of the following"-style menus;
- eventually, sending the word "ppp" (a common terminal server command).
If all of this fails, wvdial just runs pppd(8) and hopes for the best. It will bring up the connection, and then wait patiently for you to drop the link by pressing CTRL-C.
OPTIONSSeveral options are recognized by wvdial.
- -c, --chat
- Run wvdial as a chat replacement from within pppd, instead of the more normal method of having wvdial negotiate the connection and then call pppd.
- -C, --config=CONFIGFILE
- Run wvdial with CONFIGFILE as the configuration file, instead of /etc/wvdial.conf. This is mainly useful only if you want to have per-user configurations, or you want to avoid having dial-up information (usernames, passwords, calling card numbers, etc.) in a system wide configuration file.
- -n, --no-syslog
- Don't output debug information to the syslog daemon (only useful together with --chat).
wvdial is normally run without command line options, in which case it reads its configuration from the [Dialer Defaults] section of /etc/wvdial.conf. (The configuration file is described in more detail in wvdial.conf(5) manual page.)
One or more SECTIONs of /etc/wvdial.conf may be specified on the command line. Settings in these sections will override settings in [Dialer Defaults].
For example, the command:
- wvdial phone2
If more than one section is specified, they are processed in the order they are given. Each section will override all the sections that came before it.
For example, the command:
- wvdial phone2 pulse shh
Using this method, it is possible to easily configure wvdial to switch between different internet providers, modem init strings, account names, and so on without specifying the same configuration information over and over.
BUGS"Intelligent" programs are frustrating when they don't work right. This version of wvdial has only minimal support for disabling or overriding its "intelligence", with the "Stupid Mode", "Login Prompt", and "Password Prompt" options. So, in general if you have a nice ISP, it will probably work, and if you have a weird ISP, it might not.
Still, it's not much good if it doesn't work for you, right? Don't be fooled by the fact that wvdial finally made it to version 1.00; it could well contain many bugs and misfeatures. Let us know if you have problems by sending e-mail to <[email protected]>.
You may encounter some error messages if you don't have write access to /etc/ppp/pap-secrets and /etc/ppp/chap-secrets. Unfortunately, there's really no nice way around this yet.
- Configuration file which contains modem, dialing, and login information. See wvdial.conf(5).
- Serial port devices.
- Required for correct authentication in pppd version 2.3.0 or newer.
- Contains a list of usernames and passwords used by pppd for authentication. wvdial maintains this list automatically.