SYNOPSISarpwatch [ -dN ]
[ -f datafile ]
[ -i interface ]
[ -n net[/width ]]
[ -r file ]
[ -s sendmail_path ]
[ -p ]
[ -a ]
[ -m addr ]
[ -u username ]
[ -R seconds ]
[ -Q ]
[ -z ignorenet/ignoremask ]
DESCRIPTIONArpwatch keeps track for ethernet/ip address pairings. It syslogs activity and reports certain changes via email. Arpwatch uses pcap(3) to listen for arp packets on a local ethernet interface.
The -d flag is used enable debugging. This also inhibits forking into the background and emailing the reports. Instead, they are sent to stderr.
The -f flag is used to set the ethernet/ip address database filename. The default is arp.dat.
The -i flag is used to override the default interface.
The -n flag specifies additional local networks. This can be useful to avoid "bogon" warnings when there is more than one network running on the same wire. If the optional width is not specified, the default netmask for the network's class is used.
The -N flag disables reporting any bogons.
(Debian) The -s flag is used to specify the path to the sendmail program. Any program that takes the option -odi and then text from stdin can be substituted. This is useful for redirecting reports to log files instead of mail.
(Debian) The -p flag disables promiscuous operation. ARP broadcasts get through hubs without having the interface in promiscuous mode, while saving considerable resources that would be wasted on processing gigabytes of non-broadcast traffic. OTOH, setting promiscuous mode does not mean getting 100% traffic that would concern arpwatch . YMMV.
(Debian) -a By default, arpwatch reports bogons (unless -N is given) for IP addresses that are in the same subnet than the first IP address of the default interface. If this option is specified, arpwatch will report bogons about every IP addresses.
(Debian) The -m option is used to specify the e-mail address to which reports will be sent. By default, reports are sent to root on the local machine.
(Debian) The -u flag instructs arpwatch to drop root privileges and change the UID to username and GID to the primary group of username . This is recommended for security reasons, but username has to have write access to the default directory.
(Debian) The -R flag instructs arpwatch to restart in seconds seconds after the interface went down. By default, in such cases arpwatch would print an error message and exit. This option is ignored if either the -r or -u flags are used.
(Debian) The -Q flags prevents arpwatch from sending reports by mail.
(Debian) The -z flag is used to set a range of ip addresses to ignore (such as a DHCP range). Netmask is specified as 255.255.128.0.
Note that an empty arp.dat file must be created before the first time you run arpwatch.
REPORT MESSAGESHere's a quick list of the report messages generated by arpwatch(1) (and arpsnmp(1)):
- new activity
- This ethernet/ip address pair has been used for the first time six months or more.
- new station
- The ethernet address has not been seen before.
- flip flop
- The ethernet address has changed from the most recently seen address to the second most recently seen address. (If either the old or new ethernet address is a DECnet address and it is less than 24 hours, the email version of the report is suppressed.)
- changed ethernet address
- The host switched to a new ethernet address.
SYSLOG MESSAGESHere are some of the syslog messages; note that messages that are reported are also sysloged.
- ethernet broadcast
- The mac ethernet address of the host is a broadcast address.
- ip broadcast
- The ip address of the host is a broadcast address.
- The source ip address is not local to the local subnet.
- ethernet broadcast
- The source mac or arp ethernet address was all ones or all zeros.
- ethernet mismatch
- The source mac ethernet address didn't match the address inside the arp packet.
- reused old ethernet address
- The ethernet address has changed from the most recently seen address to the third (or greater) least recently seen address. (This is similar to a flip flop.)
- suppressed DECnet flip flop
- A "flip flop" report was suppressed because one of the two addresses was a DECnet address.
/var/lib/arpwatch - default directory arp.dat - ethernet/ip address database /usr/share/arpwatch/ethercodes.dat - vendor ethernet block list
AUTHORSCraig Leres of the Lawrence Berkeley National Laboratory Network Research Group, University of California, Berkeley, CA.
The current version is available via anonymous ftp:
BUGSPlease send bug reports to [email protected].
Attempts are made to suppress DECnet flip flops but they aren't always successful.
Most error messages are posted using syslog.