SYNOPSIS

DESCRIPTION

OPTIONS

Some of the arguments and requests require passing a value (e.g. Morse speed [wpm], tone (frequency) [Hz] etc.). Call "cwdaemon -h" to see default values for these arguments/requests, and ranges of accepted values.

When handling command line arguments, cwdaemon does not accept invalid, malformed, or out-of-range values passed through command line. It won't attempt to guess caller's intentions, it won't try to start with some fallback value of the argument. Instead it will just print a debug message and exit. Rejection of bad values and exiting will happen before attempting to fork.

When handling escaped requests, cwdaemon usually does not accept invalid, malformed or out-of-range vales either. But instead of exiting upon receiving request with such value, it simply prints debug message, ignores the request containing such value, and waits for next request. One exception to the rule is PTT delay: requested delay values that are too large will be clipped to maximal allowed value and then will be used by cwdaemon. Requested negative or malformed values of PTT delay will be ignored.

Print help text to stdout and exit

Command line argument: -h, --help

Escaped request: N/A

Print version information to stdout and exit

Command line argument: -V, --version

Escaped request: N/A

Set hardware keying device

Command line argument: -d, --cwdevice <device>

Escaped request: <ESC>8<device>

See chapter "DEVICES" below for more information.

Don't fork daemon, run in foreground

Command line argument: -n, --nofork

Escaped request: N/A

Debug information will be printed to stdout (unless different debug output is selected, or debug output is silenced by setting debug output verbosity).

Set network UDP port

Command line argument: -p, --port <port number>

Escaped request: <ESC>9<port number>

This escaped request is obsolete and has no effect. Command line argument works as expected.

Set process priority (niceness)

Command line argument: -P, --priority <priority>

Escaped request: N/A

Set Morse speed [wpm]

Command line argument: -s, --wpm <speed>

Escaped request: <ESC>2<speed>

Set PTT delay [ms] (TOD, Turn On Delay)

Command line argument: -t, --pttdelay <delay>

Escaped request: <ESC>d<delay>

Turn PTT keying on/off

Command line argument: N/A

Escaped request: <ESC>a<{0|1}>

0 - PTT off, 1 - PTT on

Set sound system (sound backend)

Command line argument: -x, --system <system>

Escaped request: <ESC>f<system>

See chapter "SOUND SYSTEM" below for more information.

Set sound volume for soundcard [%]

Command line argument: -v, --volume <volume>

Escaped request: <ESC>g<volume>

Set Morse weighting

Command line argument: -w, --weighting <weighting>

Escaped request: <ESC>7<weighting>

Set tone (frequency) of sound [Hz]

Command line argument: -T, --tone <tone>

Escaped request: <ESC>3<tone>

Notice that sending escaped request with value '0' silences cwdaemon.

Increase verbosity of debug output

Command line argument: -i

Escaped request: N/A

The argument can be repeated up to four times (-iiii) to gradually increase the verbosity. Alternatively you can use -y/--verbosity option.

Set verbosity threshold for debug strings

Command line argument: -y, --verbosity <threshold>

Escaped request: N/A

Alternatively you can use -i option.

See chapter "DEBUGGING" below for more information.

Set numeric value of libcw debug flags

Command line argument: -I, --libcwflags <flags>

Escaped request: N/A

Set debug output

Command line argument: -f, --debugfile <output>

Escaped request: N/A

Print debug information to <output> instead of stdout. Value of <output> can be explicitly stated as "stdout" (when not forking). Value of <output> can be also "stderr" (when not forking). Special value of <output> being "syslog" is reserved for future use. For now it will be rejected as invalid. Passing path to disc file as value of <output> works in both situations: when forking and when not forking.

Reset some of cwdaemon parameters

Command line argument: N/A

Escaped request: <ESC>0

The request resets program's parameters to cwdaemon default values, unless the defaults were overridden with command line arguments - then the values passed in command line are used.

Abort currently sent message

Command line argument: N/A

Escaped request: <ESC>4

Exit (close) daemon

Command line argument: N/A

Escaped request: <ESC>5

Set word mode

Command line argument: N/A

Escaped request: <ESC>6

Set SSB way

Command line argument: N/A

Escaped request: <ESC>b<{0|1}

0 - microphone, 1 - soundcard

Tune for a number of seconds

Command line argument: N/A

Escaped request: <ESC>c<seconds>

Tune for <seconds> seconds. The tuning is performed by both selected sound system, and by current hardware keying device.

Set band switch output

Command line argument: N/A

Escaped request: <ESC>e<value>

This argument sets band switch output on parport bits 9 (MSB), 8, 7, 2 (LSB).

DEVICES

For parallel ports on Linux try parport0 (default) or parport1, and on FreeBSD, ppi0 (default), ppi1, etc. OpenBSD does not support parallel port operation, and defaults to 'tty00'.

For completeness, a dummy 'null' device is provided. This device does exactly nothing (no rig keying, no ssb keying, etc.).

SOUND SYSTEM

'c' - console buzzer (PC speaker) - default system,

'o' - OSS,

'a' - ALSA,

'p' - PulseAudio,

'n' - none - no audio,

's' - soundcard - autoselect from OSS/ALSA/PulseAudio.

DEBUGGING

The verbosity threshold can be specified through command line arguments: -i, -y, or --verbosity. -y and --verbosity accept "threshold" value (single character) as specified below:

'n' - none

'e' - errors

'w' - warnings (default)

'i' - information

'd' - details

By default the threshold is set to "warnings" - cwdaemon will print all errors and warnings. Changing the threshold to "information" will make the cwdaemon print errors, warnings, and information.

Debug strings can be printed to stdout, stderr, or disc file. Printing to stdout or stderr is available only if cwdaemon has not forked. Printing to disc file is available regardless of whether cwdaemon has forked or not. You can specify intended debug output using -f or --debugfile command line argument. Values "stdout" and "stderr" passed to cwdaemon with these arguments are recognized as special file names. "syslog" value is also treated as special value, but is not supported at the moment. Every other value will be treated as path to disc file. "stdout" is a default debug output for non-forked cwdaemon. You don't have to specify this explicitly through command line arguments, but you can.

Regardless of values passed through -f or --debugfile arguments, cwdaemon opens a syslog file and (when forked) prints some (few) messages to the syslog. There is no way to override this at the moment. Which messages are always printed to syslog, and which can be printed to other file, is settled for now, but may be changed in the future. Don't depend too much on current setup.

AUTHOR

Since 2012 the main developer is Kamil Ignacak <[email protected]>.