Other Alias
ipsec_get_policylen, ipsec_dump_policyLIBRARY
Lb libipsecSYNOPSIS
In netinet6/ipsec.h Ft char * Fn ipsec_set_policy char *policy int len Ft int Fn ipsec_get_policylen char *buf Ft char * Fn ipsec_dump_policy char *buf char *delimDESCRIPTION
Fn ipsec_set_policy generates an IPsec policy specification structure, namely struct sadb_x_policy and/or struct sadb_x_ipsecrequest from a human-readable policy specification. The policy specification must be given as a C string Fa policy and its length Fa len . Fn ipsec_set_policy will return a buffer with the corresponding IPsec policy specification structure. The buffer is dynamically allocated, and must be free(3)Apd by the caller.You can get the length of the generated buffer with Fn ipsec_get_policylen (i.e. for calling setsockopt(2)).
Fn ipsec_dump_policy converts an IPsec policy structure into human-readable form. Therefore, Fn ipsec_dump_policy can be regarded as the inverse function to Fn ipsec_set_policy . Fa buf points to an IPsec policy structure, struct sadb_x_policy Fa delim is a delimiter string, which is usually a blank character. If you set Fa delim to NULL a single whitespace is assumed. Fn ipsec_dump_policy returns a pointer to a dynamically allocated string. It is the caller's responsibility to free(3) it.
Fa policy is formatted as either of the following:
- direction [priority specification] discard
-
direction
must be
in
out
or
fwd
direction
specifies in which direction the policy needs to be applied.
The non-standard direction
fwd
is substituted with
in
on platforms which do not support forward policies.
priority specification is used to control the placement of the policy within the SPD. The policy position is determined by a signed integer where higher priorities indicate the policy is placed closer to the beginning of the list and lower priorities indicate the policy is placed closer to the end of the list. Policies with equal priorities are added at the end of the group of such policies.
Priority can only be specified when libipsec has been compiled against kernel headers that support policy priorities (Linux >= 2.6.6). It takes one of the following formats:
- {priority,prio} offset
- offset is an integer in the range -2147483647..214783648.
- {priority,prio} base {+,-} offset
-
base
is either
low (-1073741824)
def (0)
or
high (1073741824)
offset is an unsigned integer. It can be up to 1073741824 for positive offsets, and up to 1073741823 for negative offsets.
The interpretation of policy priority in these functions and the kernel DOES differ. The relationship between the two can be described as p(kernel) = 0x80000000 - p(func)
With discard policy, packets will be dropped if they match the policy.
- direction [priority specification] entrust
- entrust means to consult the SPD defined by setkey(8).
- direction [priority specification] bypass
- bypass means to bypass the IPsec processing. (the packet will be transmitted in clear) This is for privileged sockets.
- direction Bo priority specification Bc ipsec request ...
-
ipsec
means that the matching packets are subject to IPsec processing.
ipsec
can be followed by one or more
request
strings, which are formatted as below:
- protocol / mode / src - dst [/level ]
-
protocol
is either
ah
esp
or
ipcomp
mode is either transport or tunnel
src and dst specifies the IPsec endpoint. src always means the ``sending node'' and dst always means the ``receiving node'' Therefore, when direction is in dst is this node and src is the other node (peer) If mode is transport Both src and dst can be omitted.
level must be set to one of the following: default , use , require or unique default means that the kernel should consult the system default policy defined by sysctl(8), such as net.inet.ipsec.esp_trans_deflev See ipsec(4) regarding the system default. use means that a relevant SA can be used when available, since the kernel may perform IPsec operation against packets when possible. In this case, packets can be transmitted in clear (when SA is not available) or encrypted (when SA is available) require means that a relevant SA is required, since the kernel must perform IPsec operation against packets. unique is the same as require but adds the restriction that the SA for outbound traffic is used only for this policy. You may need the identifier in order to relate the policy and the SA when you define the SA by manual keying. You can put the decimal number as the identifier after unique like unique : number number must be between 1 and 32767 . If the request string is kept unambiguous, level and slash prior to level can be omitted. However, it is encouraged to specify them explicitly to avoid unintended behavior. If level is omitted, it will be interpreted as default
Note that there are slight differences to the specification of setkey(8). In the specification of setkey(8), both entrust and bypass are not used. Refer to setkey(8) for details.
Here are several examples (long lines are wrapped for readability)
in discard out ipsec esp/transport//require in ipsec ah/transport//require out ipsec esp/tunnel/10.1.1.2-10.1.1.1/use in ipsec ipcomp/transport//use esp/transport//use
RETURN VALUES
Fn ipsec_set_policy returns a pointer to the allocated buffer with the policy specification if successful; otherwise a NULL pointer is returned. Fn ipsec_get_policylen returns a positive value (meaning the buffer size) on success, and a negative value on errors. Fn ipsec_dump_policy returns a pointer to a dynamically allocated region on success, and NULL on errors.HISTORY
The functions first appeared in the WIDE/KAME IPv6 protocol stack kit.