SYNOPSIS

In sys/types.h In netgraph/ng_source.h

DESCRIPTION

The source node acts as a source of packets according to the parameters set up using control messages and input packets. The node type is used primarily for testing and benchmarking.

HOOKS

The source node has two hooks: input and output The output hook must remain connected, its disconnection will shutdown the node.

OPERATION

The operation of the node is as follows. Packets received on the input hook are queued internally. When output hook is connected, node assumes that its neighbour node is of ng_ether4 node type. The neighbour is queried for its interface name. The node then uses queue of the interface for its evil purposes. The node also disables autosrc option on neighbour ng_ether4 node. If interface name cannot be obtained automatically, it should be configured explicitly with the NGM_SOURCE_SETIFACE control message, and autosrc should be turned off on ng_ether4 node manually.

Once interface is configured, upon receipt of a NGM_SOURCE_START control message the node starts sending the previously queued packets out the output hook on every clock tick as fast as the connected interface will take them. While active, on every clock tick the node checks the available space in the interface queue and sends that many packets out its output hook. Once the number of packets indicated in the start message has been sent, or upon receipt of a NGM_SOURCE_STOP message, the node stops sending data.

CONTROL MESSAGES

This node type supports the generic control messages as well as the following, which must be sent with the NGM_SOURCE_COOKIE attached.

NGM_SOURCE_GET_STATS (getstats )

Returns a structure containing the following fields:

outOctets

The number of octets/bytes sent out the output hook.

outFrames

The number of frames/packets sent out the output hook.

queueOctets

The number of octets queued from the input hook.

queueFrames

The number of frames queued from the input hook.

startTime

The time the last start message was received.

endTime

The time the last end message was received or the output packet count was reached.

elapsedTime

Either endTime - startTime or current time - startTime

NGM_SOURCE_CLR_STATS (clrstats )

Clears and resets the statistics returned by getstats (except queueOctets and queueFrames )

NGM_SOURCE_GETCLR_STATS (getclrstats )

As getstats but clears the statistics at the same time.

NGM_SOURCE_START (start )

This message requires a single Vt uint64_t parameter which is the number of packets to send before stopping. Node starts sending the queued packets out the output hook. The output hook must be connected and node must have interface configured.

NGM_SOURCE_STOP (stop )

Stops the node if it is active.

NGM_SOURCE_CLR_DATA (clrdata )

Clears the packets queued from the input hook.

NGM_SOURCE_SETIFACE (setiface )

This message requires the name of the interface to be configured as an argument.

NGM_SOURCE_SETPPS (setpps )

This message requires a single Vt uint32_t parameter which puts upper limit on the amount of packets sent per second.

NGM_SOURCE_SET_TIMESTAMP (settimestamp )

This message specifies that a timestamp (in the format of a Vt struct timeval ) should be inserted in the transmitted packets. This message requires a structure containing the following fields:

offset

The offset from the beginning of the packet at which the timestamp is to be inserted.

flags

Set to 1 to enable the timestamp.

NGM_SOURCE_GET_TIMESTAMP (gettimestamp )

Returns the current timestamp settings in the form of the structure described above.

NGM_SOURCE_SET_COUNTER (setcounter )

This message specifies that a counter should be embedded in transmitted packets. Up to four counters may be independently configured. This message requires a structure containing the following fields:

offset

The offset from the beginning of the packet at which the counter is to be inserted.

flags

Set to 1 to enable the counter.

width

The byte width of the counter. It may be 1, 2, or 4.

next_val

The value for the next insertion of the counter.

min_val

The minimum value to be used by the counter.

max_val

The maximum value to be used by the counter.

increment

The value to be added to the counter after each insertion. It may be negative.

index

The counter to be configured, from 0 to 3.

NGM_SOURCE_GET_COUNTER (getcounter )

This message requires a single Vt uint8_t parameter which specifies the counter to query. Returns the current counter settings in the form of the structure described above.

SHUTDOWN

This node shuts down upon receipt of a NGM_SHUTDOWN control message, when all hooks have been disconnected, or when the output hook has been disconnected.

EXAMPLES

Attach the node to an ng_ether4 node for an interface. If ng_ether is not already loaded you will need to do so. For example, these commands load the ng_ether module and attach the output hook of a new source node to orphans hook of the bge0: ng_ether node.

kldload ng_ether
ngctl mkpeer bge0: source orphans output

At this point the new node can be referred to as ``bge0:orphans '' The node can be given its own name like this:

"ngctl name bge0:orphans src0"

After which it can be referred to as ``src0: ''

Once created, packets can be sent to the node as raw binary data. Each packet must be delivered in a separate netgraph message.

The following example uses a short Perl script to convert the hex representation of an ICMP packet to binary and deliver it to the source node's input hook via nghook(8):

perl -pe 's/(..)[ \t\n]*/chr(hex($1))/ge' <<EOF | nghook src0: input
ff ff ff ff ff ff 00 00 00 00 00 00 08 00 45 00
00 54 cb 13 00 00 40 01 b9 87 c0 a8 2b 65 0a 00
00 01 08 00 f8 d0 c9 76 00 00 45 37 01 73 00 01
04 0a 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15
16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25
26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35
36 37
EOF

To check that the node has queued these packets you can get the node statistics:

ngctl msg bge0:orphans getstats
Args:   { queueOctets=64 queueFrames=1 }

Send as many packets as required out the output hook:

"ngctl msg bge0:orphans start 16"

Either wait for them to be sent (periodically fetching stats if desired) or send the stop message:

"ngctl msg bge0:orphans stop"

Check the statistics (here we use getclrstats to also clear the statistics):

ngctl msg bge0:orphans getclrstats
Args:   { outOctets=1024 outFrames=16 queueOctets=64 queueFrames=1
startTime={ tv_sec=1035305880 tv_usec=758036 } endTime={ tv_sec=1035305880
tv_usec=759041 } elapsedTime={ tv_usec=1005 } }

The times are from Vt struct timeval Ns s , the tv_sec field is seconds since the Epoch and can be converted into a date string via TCL's [clock format] or via the date(1) command:

date -r 1035305880
Tue Oct 22 12:58:00 EDT 2002

HISTORY

The node type was implemented in Fx 4.8 .

AUTHORS

An Dave Chapeskie