SYNOPSIS

perfquery [-d(ebug)] [-G(uid)] [-e(xtended)] [-a(ll_ports)] [-l(oop_ports)] [-r(eset_after_read)] [-R(eset_only)] [-C ca_name] [-P ca_port] [-t(imeout) timeout_ms] [-V(ersion)] [-h(elp)] [<lid|guid> [[port] [reset_mask]]]

DESCRIPTION

perfquery uses PerfMgt GMPs to obtain the PortCounters (basic performance and error counters) or PortExtendedCounters from the PMA at the node/port specified. Optionally shows aggregated counters for all ports of node. Also, optionally, reset after read, or only reset counters.

Note: In both PortCounters and PortCountersExtended, components that represent Data (e.g. PortXmitData and PortRcvData) indicate octets divided by 4 rather than just octets.

Note: Inputting a port of 255 indicates an operation be performed on all ports.

OPTIONS

-e, --extended

show extended port counters rather than (basic) port counters. Note that extended port counters attribute is optional.

-a, --all_ports

show aggregated counters for all ports of the destination lid or reset all counters for all ports. If the destination lid does not support the AllPortSelect flag, all ports will be iterated through to emulate AllPortSelect behavior.

-l, --loop_ports

If all ports are selected by the user (either through the -a option or port 255) iterate through each port rather than doing than aggregate operation.

-r, --reset_after_read

reset counters after read

-R, --Reset_only

only reset counters

COMMON OPTIONS

Most OpenIB diagnostics take the following common flags. The exact list of supported flags per utility can be found in the usage message and can be shown using the util_name -h syntax.

# Debugging flags

-d raise the IB debugging level.
        May be used several times (-ddd or -d -d -d).

-e show send and receive errors (timeouts and others)

-h show the usage message

-v increase the application verbosity level.
        May be used several times (-vv or -v -v -v)

-V show the version info.

# Addressing flags

-G use GUID address argument. In most cases, it is the Port GUID.
        Example:
        "0x08f1040023"

-s <smlid> use 'smlid' as the target lid for SM/SA queries.

# Other common flags:

-C <ca_name> use the specified ca_name.

-P <ca_port> use the specified ca_port.

-t <timeout_ms> override the default timeout for the solicited mads.

Multiple CA/Multiple Port Support

When no IB device or port is specified, the port to use is selected by the following criteria:

1. the first port that is ACTIVE.

2. if not found, the first port that is UP (physical link up).

If a port and/or CA name is specified, the user request is attempted to be fulfilled, and will fail if it is not possible.

EXAMPLES

perfquery # read local port performance counters

perfquery 32 1 # read performance counters from lid 32, port 1

perfquery -e 32 1 # read extended performance counters from lid 32, port 1

perfquery -a 32 # read perf counters from lid 32, all ports

perfquery -r 32 1 # read performance counters and reset

perfquery -e -r 32 1 # read extended performance counters and reset

perfquery -R 0x20 1 # reset performance counters of port 1 only

perfquery -e -R 0x20 1 # reset extended performance counters of port 1 only

perfquery -R -a 32 # reset performance counters of all ports

perfquery -R 32 2 0x0fff # reset only error counters of port 2

perfquery -R 32 2 0xf000 # reset only non-error counters of port 2

AUTHOR

Hal Rosenstock

<[email protected]>