SYNOPSIS
uisp [OPTION].. -dprog=TYPE -dpart=AT90XXX --FUNCTION.. [if=SOURCE] [of=DEST]DESCRIPTION
Programming Methods:
-dprog=<method>-
- avr910
- Standard Atmel Serial Programmer/Atmel Low Cost Programmer
- pavr
- http://www.avr1.org/pavr/pavr.html
- stk500
- Atmel STK500
- dapa
- Direct AVR Parallel Access
- stk200
- Parallel Starter Kit STK200, STK300
- abb
- Altera ByteBlasterMV Parallel Port Download Cable
- atdh
- Atmel-ISP Download Cable (P/N ATDH1150VPC)
- avrisp
- Atmel AVR ISP (?)
- bsd
- http://www.bsdhome.com/avrdude/ (parallel)
- fbprg
- http://ln.com.ua/~real/avreal/adapters.html (parallel)
- dt006
- http://www.dontronics.com/dt006.html (parallel)
- maxi
- Investment Technologies Maxi (parallel)
- dm04
- Datamekatronik 2004 (parallel)
- dasa
- serial (RESET=RTS SCK=DTR MOSI=TXD MISO=CTS)
- dasa2
- serial (RESET=!TXD SCK=RTS MOSI=DTR MISO=CTS)
- dasa3
- serial (RESET=!DTR SCK=RTS MOSI=TXD MISO=CTS)
Target Device Selection:
- -dpart=part
- Set target abbreviated name or number. For some programmers, if -dpart is not given programmer's supported devices are listed. Set -dpart=auto for auto-select. Auto-select does not work with all programmers, so it is recommended to always specify a target device explicitly.
Parallel Device Settings:
- -dlpt=address|device name
- specify device name (Linux ppdev, FreeBSD ppi, serial) or direct I/O parallel port address (0x378, 0x278, 0x3BC)
- -dno-poll
- Program without data polling (a little slower)
- -dno-retry
- Disable retries of program enable command
- -dvoltage=value
- Set timing specs according to the power supply voltage in [V] (default 3.0)
- -dt_sck=time
- Set minimum SCK high/low time in micro-seconds (default 5)
- -dt_wd_flash=time
- Set FLASH maximum write delay time in micro-seconds
- -dt_wd_eeprom=time
- Set EEPROM maximum write delay time in micro-seconds
- -dt_reset=time
- Set reset inactive (high) time in micro-seconds
- -dinvert=[sck[,mosi[,miso[,reset]]]]]
- Invert specified lines Use -v=3 option to see current settings.
- -d89
- Allow parallel programming of AT89S51 and AT89S52 devices.
Atmel Low Cost Programmer Serial Device Settings:
- -dserial=device name
- Set serial interface as /dev/ttyS* (default /dev/avr)
- -dspeed=1200|2400|4800|9600|19200|38400|57600|115200
- Set speed of the serial interface (default 19200)
Stk500 specific options:
- -dhiv
- Use Hi-V programming instead of SPI (default is SPI).
- --rd_aref
- Read the ARef Voltage. Note that due to a bug in the stk500 firmware, the read value is sometimes off by 0.1 from the actual value measured with a volt meter.
- --wr_aref=value
- Set the ARef Voltage. Valid values are 0.0 to 6.0 volts in 0.1 volt increments. Value can not be larger than the VTarget value.
- --rd_vtg
- Read the Vtarget Voltage. Note that due to a bug in the stk500 firmware, the read value is sometimes off by 0.1 from the actual value measured with a volt meter.
- --wr_vtg=value
- Set the VTarget Voltage. Valid values are 0.0 to 6.0 volts in 0.1 volt increments. Value can not be smaller than the ARef value.
- --rd_osc
- Read the oscillator frequency in Hertz.
- --wr_osc=value
- Set the oscillator frequency in Hertz, from 14.06 to 3686400.
Functions:
- --upload
- Upload "input_file" to the AVR memory.
- --verify
- Verify "input_file" (processed after the --upload opt.)
- --download
- Download AVR memory to "output_file" or stdout.
- --erase
- Erase device.
- --segment=flash|eeprom|fuse
- Set active segment (auto-select for AVA Motorola output)
Fuse/Lock Bit Operations:
- --rd_fuses
- Read all fuses and print values to stdout
- --wr_fuse_l=byte
- Write fuse low byte
- --wr_fuse_h=byte
- Write fuse high byte
- --wr_fuse_e=byte
- Write fuse extended byte
- --wr_lock=byte
-
Write lock bits. Argument is a byte where each bit is:
Bit5 -> blb12
Bit4 -> blb11
Bit3 -> blb02
Bit2 -> blb01
Bit1 -> lb2
Bit0 -> lb1 - --lock
- Write lock bits [old method; deprecated].
Files:
- if=filename
- Input file for the --upload and --verify functions in Motorola S-records (S1 or S2) or 16 bit Intel format
- of=filename
- Output file for the --download function in Motorola S-records format, default is standard output
Other Options:
- -v=level
- Set verbose level (-v equals -v=2, min/max: 0/4, default 1)
- --hash=perbytes
- Print hash (default is 32 bytes)
- --help -h
- Help
- --version
- Print version information
- --terminal
- Invoke shell-like terminal
AUTHOR
Written by Uros Platise.REPORTING BUGS
Report bugs to <[email protected]>COPYRIGHT
(c) 1997-1999 Uros Platise, 2000-2004 Marek Michalkiewiczuisp is free software, covered by the GNU General Public License. You are welcome to change it and/or distribute copies of it under the conditions of the GNU General Public License.