SYNOPSIS
divaload controller protocol [options]DESCRIPTION
divaload is used to setup the Eicon Diva card for the proper configuration.OPTIONS
- controller
-
selects the controller (card). This can be either:
-c n
where n is the controller number, or
-all
to operate on all cards. - protocol
-
can be one of the following:
-f 1TR6 Germany, old protocol for PABX................ PRI & BRI -f ETSI DSS1, Europe (Germany, ...)................... PRI & BRI -f FRANC VN3, France, old protocol for PABX............ PRI & BRI -f BELG NET3, Belgien, old protocol for PABX.......... PRI & BRI -f SWED DSS1 with CRC4 off, Sweden, Benelux........... PRI -f NI NI1, NI2, North America, National ISDN........ PRI & BRI -f 5ESS 5ESS, North America, AT&T..................... PRI & BRI -f JAPAN Japan, INS-NET64.............................. PRI & BRI -f ATEL ATEL, Australia, old TPH1962.................. PRI & BRI -f US North America, Auto Detect.................... BRI -f ITALY DSS1, Italy................................... PRI & BRI -f TWAN DSS1, Taiwan.................................. PRI & BRI -f AUSTRAL Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI -f 4ESS_SDN 4ESS Software Defined Network................. PRI -f 4ESS_SDS 4ESS Switched Digital Service................. PRI -f 4ESS_LDS 4ESS Long Distance Service.................... PRI -f 4ESS_MGC 4ESS Megacom.................................. PRI -f 4ESS_MGI 4ESS Megacom International.................... PRI -f HONGKONG Hongkong...................................... PRI & BRI -f RBSCAS Robbed Bit Signaling, CAS..................... PRI -f QSIG QSIG, Intra PABX link protocol................ PRI & BRI
The following options may be given to divaload.
- -e [1,2,3]
- set Layer 1 framing on PRI Adapter
-
1
- doubleframing (NO CRC4)
2 - multiframing (CRC4)
3 - autodetection
- -x
- set PRI Adapter in NT mode; default mode is TE
- -z
- set PRI Adapter in High Impedance state until first user application does request interface activation
- -l [1...30]
- set starting channel number on PRI Adapter. By default the allocation of channels is made on a high-to-low basis. By specifying -l you select a low-to-high allocation policy (in addition)
- -q [0..3]
- select QSIG options
-
0
- CR and CHI 2 Bytes long (default)
1 - CR 1 byte, CHI 2 bytes
2 - CR is 2 bytes, CHI is 1 byte
3 - CR and CHI 1 byte
(CR - Call Reference, CHI - B-Channel Ident.)
- -n [0...20]
- select NT2 mode and default length of DIDN (DIDN - Direct Inward Dial Number)
- -o
- turn off order checking of information elements
- -p [1,2]
- establish a permanent connection (e.g. leased line configuration)
-
1
- TE <-> TE mode, structured line
2 - NT <-> TE mode, raw line
- -s [0,1,2,3]
- D-Channel Layer 2 activation policy on BRI Adapter
-
0
- On demand
1 - Deactivation only by NT side, preferred, default
2 - Always active
3 - Always active, mode 2
- -t [0...63]
-
specifies a fixed TEI value
(Default is a automatic TEI assignment)
- -u
-
select point to point mode on BRI Adapter;
uses default TEI '0',
NT2 mode is on
- -[1...8]oad|osa|spid
-
BRI Adapter B-Channel options
Specify the Originating Address (OAD),
Originating Sub-address (OSA) and/or
Service Profile Identifier (SPID)
for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)
Example: -1oad 123456 -1spid 1234560001 - -d
-
display protocol options summary
- -w
-
select alternative protocol code directory.
default directory: "/usr/share/isdn" - -h or -?
-
help