SYNOPSIS
Dual Switch3A [.]XXXXXXXXXXXX[XX][/[ PIO.[A|B|ALL|BYTE] | sensed.[A|B|ALL|BYTE] | address | crc8 | id | locator | r_address | r_id | r_locator | type ]]
FAMILY CODE
3A
SPECIAL PROPERTIES
PIO.A PIO.B PIO.ALL PIO.BYTE
read-write, yes-noState of the open-drain output ( PIO ) pin. 0 = non-conducting (off), 1 = conducting (on).
Writing zero will turn off the switch, non-zero will turn on the switch. Reading the PIO state will return the switch setting. To determine the actual logic level at the switch, refer to the sensed property.
ALL references both channels simultaneously, comma separated.
BYTE references both channels simultaneously as a single byte, with channel A in bit 0.
sensed.A sensed.B sensed.ALL sensed.BYTE
read-only, yes-noLogic level at the PIO pin. 0 = ground. 1 = high (~2.4V - 5V ). Really makes sense only if the PIO state is set to zero (off), else will read zero.
ALL references both channels simultaneously, comma separated.
BYTE references both channels simultaneously as a single byte, with channel A in bit 0.
STANDARD PROPERTIES
address
r_address
read-only, asciiThe entire 64-bit unique ID. Given as upper case hexadecimal digits (0-9A-F).
address starts with the family code
r address is the address in reverse order, which is often used in other applications and labeling.
crc8
read-only, asciiThe 8-bit error correction portion. Uses cyclic redundancy check. Computed from the preceding 56 bits of the unique ID number. Given as upper case hexadecimal digits (0-9A-F).
family
read-only, asciiThe 8-bit family code. Unique to each type of device. Given as upper case hexadecimal digits (0-9A-F).
id
r_id
read-only, asciiThe 48-bit middle portion of the unique ID number. Does not include the family code or CRC. Given as upper case hexadecimal digits (0-9A-F).
r id is the id in reverse order, which is often used in other applications and labeling.
locator
r_locator
read-only, asciiUses an extension of the 1-wire design from iButtonLink company that associated 1-wire physical connections with a unique 1-wire code. If the connection is behind a Link Locator the locator will show a unique 8-byte number (16 character hexadecimal) starting with family code FE.
If no Link Locator is between the device and the master, the locator field will be all FF.
r locator is the locator in reverse order.
present (DEPRECATED)
read-only, yes-noIs the device currently present on the 1-wire bus?
type
read-only, asciiPart name assigned by Dallas Semi. E.g. DS2401 Alternative packaging (iButton vs chip) will not be distiguished.
ALARMS
Use the set_alarm property to set the alarm triggering criteria.DESCRIPTION
1-Wire
1-wire is a wiring protocol and series of devices designed and manufactured by Dallas Semiconductor, Inc. The bus is a low-power low-speed low-connector scheme where the data line can also provide power.Each device is uniquely and unalterably numbered during manufacture. There are a wide variety of devices, including memory, sensors (humidity, temperature, voltage, contact, current), switches, timers and data loggers. More complex devices (like thermocouple sensors) can be built with these basic devices. There are also 1-wire devices that have encryption included.
The 1-wire scheme uses a single bus master and multiple slaves on the same wire. The bus master initiates all communication. The slaves can be individually discovered and addressed using their unique ID.
Bus masters come in a variety of configurations including serial, parallel, i2c, network or USB adapters.
OWFS design
OWFS is a suite of programs that designed to make the 1-wire bus and its devices easily accessible. The underlying principle is to create a virtual filesystem, with the unique ID being the directory, and the individual properties of the device are represented as simple files that can be read and written.Details of the individual slave or master design are hidden behind a consistent interface. The goal is to provide an easy set of tools for a software designer to create monitoring or control applications. There are some performance enhancements in the implementation, including data caching, parallel access to bus masters, and aggregation of device communication. Still the fundemental goal has been ease of use, flexibility and correctness rather than speed.
DS2413
The DS2413 (3) allows control of other devices, like LEDs and relays. It differs from the DS2405 with a cleaner interface and two channels The DS2413 also has two channels like the DS2406 and DS2407 but has no memory, and no alarm. There is also varying types of switch and sensing in the DS2408, DS2409, LCD, DS276x, DS2450.Unique among the switches, the DS2413 can switch higher voltages, up to 28V.
ADDRESSING
All 1-wire devices are factory assigned a unique 64-bit address. This address is of the form:- Family Code
- 8 bits
- Address
- 48 bits
- CRC
- 8 bits
Addressing under OWFS is in hexadecimal, of form:
- 01.123456789ABC
where 01 is an example 8-bit family code, and 12345678ABC is an example 48 bit address.
The dot is optional, and the CRC code can included. If included, it must be correct.