SYNOPSIS
ledctl [OPTIONS] pattern_name=list_of_devices ...DESCRIPTION
The ledctl is an user space application designed to control LEDs associated with each slot in an enclosure or a drive bay. The LEDs of devices listed in list_of_devices are set to the given pattern pattern_name and all other LEDs are turned off. User must have root privileges to use this application.There are two types of systems: 2-LEDs systems (Activity LED, Status LED) and 3-LEDs systems (Activity LED, Locate LED, Fail LED). The ledctl application uses SGPIO and SES-2 protocol to control LEDs. The program implements IBPI patterns of SFF-8489 specification for SGPIO. Please note some enclosures do not stick close to SFF-8489 specification. It might happen that enclosure's processor will accept an IBPI pattern but it will blink the LEDs at variance with SFF-8489 specification or it has limited number of patterns supported.
LED management (AHCI) and SAF-TE protocols are not supported.
The ledctl application has been verified to work with Intel(R) storage controllers (i.e. Intel(R) AHCI controller and Intel(R) SAS controller). The application might work with storage controllers of other vendors (especially SCSI/SAS controllers). However, storage controllers of other vendors have not been tested.
The ledmon application has the highest priority when accessing LEDs. It means that some patterns set by ledctl may have no effect if ledmon is running (except Locate pattern).
The ledctl application is a part of Intel(R) Enclosure LED Utilities.
Pattern Names
The ledctl application accepts the following names for pattern_name argument according to SFF-8489 specification.- locate
- Turns Locate LED associated with the given device(s) or empty slot(s) on.
- locate_off
- Turns only Locate LED off.
- normal
- Turns Status LED, Failure LED and Locate LED off.
- off
- Turns only Status LED and Failure LED off.
- ica or degraded
- Visualizes ``In a Critical Array'' pattern.
- rebuild or rebuild_p
- Visualizes ``Rebuild'' pattern.
- ifa or failed_array
- Visualizes ``In a Failed Array'' pattern.
- hotspare
- Visualizes ``Hotspare'' pattern.
- pfa
- Visualizes ``Predicted Failure Analysis'' pattern.
- failure or disk_failed
- Visualizes ``Failure'' pattern.
- ses_abort
- SES-2 R/R ABORD
- ses_rebuild
- SES-2 REBUILD/REMAP
- ses_ifa
- SES-2 IN FAILED ARRAY
- ses_ica
- SES-2 IN CRIT ARRAY
- ses_cons_check
- SES-2 CONS CHECK
- ses_hotspare
- SES-2 HOT SPARE
- ses_rsvd_dev
- SES-2 RSVD DEVICE
- ses_ok
- SES-2 OK
- ses_ident
- SES-2 IDENT
- ses_rm
- SES-2 REMOVE
- ses_insert
- SES-2 INSERT
- ses_missing
- SES-2 MISSING
- ses_dnr
- SES-2 DO NOT REMOVE
- ses_active
- SES-2 ACTIVE
- ses_enbale_bb
- SES-2 ENABLE BYP B
- ses_enable_ba
- SES-2 ENABLE BYP A
- ses_devoff
- SES-2 DEVICE OFF
- ses_fault
- SES-2 FAULT
Patterns Translation
When non SES-2 pattern is send to device in enclosure automatic translation is being done.- locate
- locate is translated to ses_ident
- locate_off
- locate_off is translated to ~ses_ident
- normal
- normal is translated to ses_ok
- off
- off is translated to ses_ok
- degraded
- degraded is translated to ses_ica
- rebuild
- rebuild is translated to ses_rebuild
- rebuild_p
- rebuild_p is translated to ses_rebuild
- failed
- failed is translated to ses_ifa
- hotspare
- hotspare is translated to ses_hotspare
- pfa
- pfa is translated to ses_rsvd_dev
- failure
- failure is translated to ses_fault
- disk_failed
- disk_failed is translated to ses_fault
List of Devices
The application accepts a list of devices in two formats. The first format is a list with comma separated elements. The second format is a list in curly braces and elements are separated by space. See examples section bellow for details.A device is a path to file in /dev directory or in /sys/block directory. It may identify a block device, a RAID device or a container device. In case of a RAID device or a container device a state will be set for all block devices associated, respectively.
The LEDs of devices listed in list_of_devices are set to the given pattern pattern_name and all other LEDs are turned off.
OPTIONS
- -c or --config=path
- Sets a path to local configuration file. If this option is specified the global configuration file and user configuration file has no effect.
- -l or --log=path
- Sets a path to local log file. If this option is specified the global log file /var/log/ledctl.log is not used.
- -h or --help
- Prints this text out and exits.
- -v or --version
- Displays version of ledctl and information about the license and exits.
FILES
- /var/log/ledctl.log
- Global log file, used by all instances of ledctl application. To force logging to user defined file use -l option switch.
- ~/.ledctl
- User configuration file, shared between ledmon and all ledctl application instances.
- /etc/ledcfg.conf
- Global configuration file, shared between ledmon and all ledctl application instances.
EXAMPLES
The following example illustrates how to locate a single block device.
ledctl locate=/dev/sda
The following example illustrates how to turn Locate LED off for the same block device.
ledctl locate_off=/dev/sda
The following example illustrates how to locate disks of a RAID device and how to set rebuild pattern for two block devices at the same time. This example uses both formats of device list.
ledctl locate=/dev/md127 rebuild={ /sys/block/sd[a-b] }
The following example illustrates how to turn Status LED and Failure LED off for the given device(s).
ledctl off={ /dev/sda /dev/sdb }
The following example illustrates how to locate a three block devices. This example uses the first format of device list.
ledctl locate=/dev/sda,/dev/sdb,/dev/sdc
LICENSE
Copyright (c) 2009-2013 Intel Corporation.This program is distributed under the terms of the GNU General Public License as published by the Free Software Foundation. See the built-in help for details on the License and the lack of warranty.