SYNOPSIS
*** Probes ***
+FPing6
binary = /usr/bin/fping6 # mandatory
blazemode = true
hostinterval = 1.5
mininterval = 0.001
offset = 50%
packetsize = 5000
pings = 20
sourceaddress = ::1
step = 300
timeout = 1.5
tos = 0x20
usestdout = true
# [...]
*** Targets ***
probe = FPing6 # if this should be the default probe
# [...]
+ mytarget
# probe = FPing6 # if the default probe is something else
host = my.host
DESCRIPTION
Integrates FPing6 as a probe into smokeping. This probe is derived from FPing; the only difference is that the target host used for checking the fping command output is ::1 instead of localhost.VARIABLES
Supported probe-specific variables:- binary
-
The location of your fping binary.
Example value: /usr/bin/fping6
This setting is mandatory.
- blazemode
-
Send an extra ping and then discarge the first answer since the first is bound to be an outliner.
Example value: true
- hostinterval
-
The fping ``-p'' parameter, but in (possibly fractional) seconds rather than
milliseconds, for consistency with other Smokeping probes. From fping(1):
This parameter sets the time that fping waits between successive packets to an individual target.
Example value: 1.5
- mininterval
-
The fping ``-i'' parameter, but in (probably fractional) seconds rather than
milliseconds, for consistency with other Smokeping probes. From fping(1):
The minimum amount of time between sending a ping packet to any target.
Example value: 0.001
Default value: 0.01
- offset
-
If you run many probes concurrently you may want to prevent them from
hitting your network all at the same time. Using the probe-specific
offset parameter you can change the point in time when each probe will
be run. Offset is specified in % of total interval, or alternatively as
'random', and the offset from the 'General' section is used if nothing
is specified here. Note that this does NOT influence the rrds itself,
it is just a matter of when data acqusition is initiated.
(This variable is only applicable if the variable 'concurrentprobes' is set
in the 'General' section.)
Example value: 50%
- packetsize
-
The ping packet size (in the range of 12-64000 bytes).
Example value: 5000
- pings
-
How many pings should be sent to each target, if different from the global
value specified in the Database section. Note that the number of pings in
the RRD files is fixed when they are originally generated, and if you
change this parameter afterwards, you'll have to delete the old RRD
files or somehow convert them.
Example value: 20
- sourceaddress
-
The fping ``-S'' parameter . From fping(1):
Set source address.
Example value: ::1
- step
-
Duration of the base interval that this probe should use, if different
from the one specified in the 'Database' section. Note that the step in
the RRD files is fixed when they are originally generated, and if you
change the step parameter afterwards, you'll have to delete the old RRD
files or somehow convert them. (This variable is only applicable if
the variable 'concurrentprobes' is set in the 'General' section.)
Example value: 300
- timeout
-
The fping ``-t'' parameter, but in (possibly fractional) seconds rather than
milliseconds, for consistency with other Smokeping probes. Note that as
Smokeping uses the fping 'counting' mode (-C), this apparently only affects
the last ping.
Example value: 1.5
- tos
-
Set the type of service (TOS) of outgoing ICMP packets.
You need at laeast fping-2.4b2_to3-ipv6 for this to work. Find
a copy on www.smokeping.org/pub.
Example value: 0x20
- usestdout
-
Listen for FPing output on stdout instead of stderr ... (version 3.3+ sends its statistics on stdout).
Example value: true